| 37 1091 01 Rollix Slewing Ring Bearings | Basic dynamic load rating C:184 kN; d:41.275 mm; Ca min.:6 mm; Calculation factor e:0.28; Fatigue load limit Pu:21.6 kN; C:26.988 mm; Db min.:94 mm; Cb min.:7.5 mm; Da max.:90 mm; r3,4 min.:3.3 mm; db min.:54.5 mm; Da min.:87 mm; r1,2 min.:3.5 mm; rb max.:3.3 mm; ra max.:3.5 mm; T:34.925 mm; Dimension series:525; Basic static load rating C0:190 kN; Calculation factor Y0:1.1; Mass bearing:1.47 kg; |
| 2 1225 Rollix Slewing Ring Bearings | d1 ≈:458 mm; Basic static load rating C0:12700 kN; Calculation factor e:0.44; Mass bearing:245 kg; r3,4 min.:3.3 mm; d:431.8 mm; Calculation factor Y0:1.4; D1 ≈:530 mm; Basic dynamic load rating C:4840 kN; Comparative axial load rating CFa:254 kN; Calculation factor Y2:2.3; Fatigue load limit Pu:980 kN; D:571.5 mm; Thrust factor K:1.34; B:400 mm; T:400 mm; Comparative radial load rating CF:1180 kN; |
| 1 105 Rollix Slewing Ring Bearings | d:10.000 mm; Sealed Speed Rating n3:19000 rpm; Accessories:Snap-Ring; Basic Static Radial Load Rating Co:1960 N; Fillet Radius ra:0.30 mm; Basic Dynamic Radial Load Rating C:4620 N; Oil Speed Rating Open/Shielded n2:36000 rpm; D:26.0000 mm; Grease Speed Rating Open/Shielded n1:30000 rpm; B:8.00 mm; |
| 39 1091 01 Rollix Slewing Ring Bearings | Housing:FSAF 215; Cap bolt recommended tightening torque:81.3 N·m; P180°:22.2 kN; A1:79.375 mm; R2:21.431 mm; P90°:32.5 kN; Initial grease fill:136.08 g; Max. speed for PosiTrac Plus seal:1450 r/min; P150°:18.2 kN; Stabilizing ring:2 x SR-15-0; H2:28.575 mm; Labyrinth ring (dc shaft position):LOR 46; Labyrinth ring (db shaft position):LOR 79; L:285.75 mm; Da:130 mm; R1:46.038 mm; |
| 121.36.4000.990.41.1502 Standard 5 Slewing Ring Bearings | d1:247 mm; B:17 mm; r1,2 min.:1.5 mm; Mass shaft washer:2.9 kg; d:180 mm; |
| 28 0841 01 Rollix Slewing Ring Bearings | P90°:113 kN; A1:133.35 mm; Ca:89.789 mm; Mass pillow block:69.3 kg; PG:1/4 NPT; Labyrinth ring:2 x LOR 668; P120°:73.8 kN; P150°:68.1 kN; ba:63.5 mm; P60°:189 kN; Initial grease fill:382.73 g; H1:152.4 mm; Cap bolt:2 x 1-8 UNC; End plug (suffix Y):EPR 13; H2:60.325 mm; R2:36.513 mm; Pa:26.7 kN; Da:240 mm; N1:25.4 mm; P180°:84.5 kN; |
| 33 0411 01 Rollix Slewing Ring Bearings | H1:101.6 mm; dc:85.725 mm; PG:1/8 NPT; Cap bolt:1/2-13 UNC; Ca:49.809 mm; P60°:141 kN; J min.:263.525 mm; N1:23.813 mm; Cap bolt recommended tightening torque:149.1 N·m; R2:27.781 mm; S:4.763 mm; A2:149.225 mm; End plug (suffix Y):EPR 11; PosiTrac Plus contact element (dc shaft position):B10724-188; PosiTrac Plus contact element (db shaft position):B10724-113; Max. speed for PosiTrac Plus seal:1350 r/min; |
| 2 1415 Rollix Slewing Ring Bearings | Oil Speed Rating n2:8800 rpm; Basic Static Radial Load Rating Co:270000 N; B:68.00 mm; Basic Dynamic Radial Load Rating C:251000 N; d:100.000 mm; Grease Speed Rating n1:6200 rpm; Fillet Radius ra:2.00 mm; Fillet Radius rb:1.00 mm; D:180.0000 mm; |
| 1 1845 02 Rollix Slewing Ring Bearings | B:11.00 mm; D:35.0000 mm; d:15.000 mm; Fillet Radius ra:0.64 mm; Fillet Radius rb:0.30 mm; Basic Dynamic Radial Load Rating C:9750 N; Basic Static Radial Load Rating Co:5100 N; Oil Speed Rating n2:24000 rpm; Grease Speed Rating n1:19000 rpm; |
| 28 0941 01 Rollix Slewing Ring Bearings | ra max.:4 mm; Basic static load rating C0:7650 kN; Mass bearing (including seat washer where applicable):140 kg; d1 ≈:1054 mm; Basic dynamic load rating C:630 kN; Minimum load factor A:300; d:900 mm; Limiting speed:500 r/min; H:95 mm; da min.:991 mm; Da max.:969 mm; D:1060 mm; Fatigue load limit Pu:90 kN; D1 ≈:906 mm; r1,2 min.:5 mm; Reference speed:360 r/min; |
| 6 04 Rollix Slewing Ring Bearings | d2 ≈:82.9 mm; B:40 mm; d:75 mm; D:105 mm; Operating clearance factor k2:0.142; Da max.:100 mm; s2 max.:5 mm; Basic dynamic load rating C:166 kN; D1 ≈:96.1 mm; Fatigue load limit Pu:30 kN; Mass bearing:3.9 kg; Basic static load rating C0:232 kN; da min.:79.6 mm; r1,2 min.:1 mm; Limiting speed:130 r/min; da max.:84.1 mm; Misalignment factor k1:0.083; ra max.:1 mm; |
| 75074A Franke Slewing Ring Bearings | B:16 mm; Permissible sliding velocity v max.:0.5 m/s; Specific static load factor K0:45 N/mm²; Tolerance shaft:e7; h:19 mm; α:105 °; Specific dynamic load factor K:25 N/mm²; Permissible sliding velocity v min.:0 m/s; D:25 mm; Tolerance housing:H7; Mass bushing:0.03 kg; d:18 mm; a:3 mm; Coefficient of friction µ max.:0.15; Coefficient of friction µ min.:0.08; |